SCOOP ORNAMENT

INSIDE-OUT ORNAMENT

Robert Chastain

MATERIALS NEEDED:
4 pieces of plywood, ½" x 3½" x 3½"
4 hardwood blocks ¾" x ¾" x 6" or to fit pattern
Yellow glue
assorted grits of abrasive paper and
random orbit sander discs
hanger
Deft or finish of choice

TOOLS NEEDED:
Table saw
ruler
drill press with a 1/16" drill bit
scroll saw
lathe with assorted chisels
small hand saw and
a shop-built disc sander

ROUTED INLAY ORNAMENT

John Lucas

TOOLS NEEDED:
Trim router with platform
indexing wheel

SPECIAL SHOPMADE MANDRELS

Harry Gilliand

SUPPLIES NEEDED:
2" x 2" x 3" block of hard wood or sized to fit your needs

TOOLS NEEDED:
Tap to match threads on your lathe spindle
drill bit(s) to drill pilot hole for your tap
drill press
hand screws
lathe
assorted chisels

BUDSTIKKE

Gothard Knutson

TOOLS NEEDED:
Bandsaw
lathe with assorted chisels
4-jawed chuck
live tailstock center
shopmade wooden plug
Jacob's chuck with a 1¼" spade bit and a ¼" twist drill bit
ruler
calipers

MATERIALS NEEDED:
2 ½" X 14" basswood blank (or species of choice)
epoxy or polyurethane glue (optional)
½" copper plumbing end cap
assorted grits of abrasive paper
¼" x 2½" metal rod or dowel

BOTTLE STOPPER TRIMMING JIG

Wes Jones

TOOLS NEEDED:
Table saw
lathe with a 4-jawed chuck and a small skew
drill chuck and either a 9/16" or ⅝" spade bit
ruler
bandsaw with fence
either a belt or disc sander

SUPPLIES NEEDED:
1 piece, 1½" x 3" x 7" construction grade pine

RED MALLEE TEXTURED STARBURST BOWL

TOOLS NEEDED:
Scroll chuck, 2 ½” jaws
Standard drive spur
Live tailstock center
Dividers, steel rule
½” bowl gouge with a swept back grind
⅜” bowl gouge with a square grind
⅝” skew and ⅜” round skew (not critical)
¼” parting tool
carver's vise with chuck adapter (or tool post adapter)
reciprocating carver and blades (or carver's gouges)
Dremel tool (or equivalent) and a ⅝” diameter by 1/16” toothed cutter on an arbor
     (like a small circular saw blade only relatively thicker re-ground to a 45° edge.
     Carefully touch each side of the rotating cutter to a grind stone until the edge is V-shaped
     but the cutter teeth are still intact)
Round microplane tool
5” vacuum chuck
Drill press, 1¼” Forstner bit
2” sanding arbor and sanding discs (up to 600 grit or higher)
white 3M buffing pad (non-abrasive) or white diamond buffing compound

MATERIALS USED:
Red Mallee burl cap (roughly oval shaped, about 2½" x 9" x 14")
WaterLox finish or finish of choice
Cheese cloth
Wet-or-dry 600 grit abrasive paper

PUZZLE PEN

Barry Gross

SUPPLIES NEEDED:
Kallenshaan Woods Puzzle Kit (www.kallenshaanwoods.com)
Sterling Silver "Baron" kit available, from Arizona Silhouette (www.arizonasilhouette.com)
Rhodium 22k "Statesman Junior" kit, available from Craft Supply (www.woodturnerscatalog.com)
Black spray paint
Masking tape
Rubber bands
Thin cyanoacrylate glue
Sanding material of choice
EEE Cream & Behlen’s Woodturners Finish or finish of choice
Abralon Sanding Pads, available from BG Artforms 888-717-4202, Item #PKF-2

TOOLS REQUIRED:
Lathe with a small skew or a Spindlemaster
hobby knife
squaring jig (available from Penn State industries (www.pennstateind.com).